|Home > Astronomy > William Herschel Telescope > ING FITS Headers|
ING FITS Headers
Data obtained with ING common-user instruments are accompanied by FITS headers(refs 1,2,5) summarising the state of the telescope, instrument and detector, e.g.:
AZSTART = 298.644448 / Azimuth at start of observation (degrees) CAT-DEC = '+39:55:13.00' / Target Declination CAT-EPOC= 2000.00 / Target epoch of proper motions CAT-EQUI= 'J2000.00' / Equinox of target coordinates CAT-NAME= 'HDS930 ' / Target input-catalogue nameThe pages linked below show example FITS headers from science and calibration exposures with ING instruments at the WHT:
The pages linked below show an ING FITS header (of the above ACAM calibration exposure), reordered:
The rather unhelpful order of the headers results from them being written out in a series of pre-defined packets (called OBSVATON, TELESCOP, AUTOGUID etc.). The format of each header follows the usual FITS standards(ref 3).
The names of headers relating to a given instrument usually begin with the name of the instrument (or an abbreviation) e.g. ACAM or ISI (for ISIS). Headers whose names begin 'CAGA' refer to components within the WHT Cassegrain acquisition and guiding box. The names of most other headers are standard FITS keywords ('DATE-OBS') or are based on those in use at AAO (e.g. 'RUN') and UKIRT, and on the names expected by iraf data-reduction programs (e.g. 'AIRMASS', 'DARKTIME', 'DISPAXIS', 'EPOCH', 'EXPTIME', 'IMAGETYP', 'IRAFNAME', 'OBSERVAT').
To search for a header containing a given string, grep the output from imhead. E.g. to search for headers recording the CCD window in use when obtaining image r1234567.fit, issue the following command at the iraf prompt:
ecl> imhead r1234567 l+ | grep WIN
Below are listed current WHT headers which are common to data from most instruments (the INT ones are similar).
RA and DEC record the position of the telescope after any 'offset' command. A change in position due to a 'tweak' command is not reflected in the headers. The applied offsets are recorded by RAOFF, DECOFF (offsets in tangent plane), XAPNOM and YAPNOM (nominal aperture offsets), and XAPOFF, YAPOFF (total aperture offsets).
ROTSKYPA is the sky position angle, ROTTRACK records whether the rotator is tracking sky.
The angular positions of the telescope, dome and rotator relative to the ground, at the start and end of the exposure, are recorded by: AZSTART, AZEND, ZDSTART, ZDEND (telescope); DAZSTART, DAZEND (dome); AMSTART, AMEND (and AIRMASS = effective mean airmass); and MNTPASTA, MNTPAEND (rotator mount PA). PARANSTA, PARANEND record the parallactic angle. VIGNETTE records whether the telescope is vignetted by the dome. TELSTAT records the telescope status, e.g. 'MOVING' at the end of the observation. The values of most of the other telescope headers mentioned here are recorded at the start of the exposure.
The name and geographical coordinates of the telescope are recorded in TELESCOP (and SLATEL, the name by which it is known to the SLALIB package), LATITUDE, LONGITUD and HEIGHT.
TELFOCUS is the nominal position of the WHT focus drive, prior to applying corrections FOCUSTMP, FOCUSALT and FOCUSTMP for temperature, elevation and filter respectively. The actual focus position (sum of the above 4 numbers) is given by ACTELFOC.
FSTATION records the focal station. The allowed values for the WHT are 'Cassegrain', 'NasmythD' (for Nasmyth drive side), 'NasmythCW' (for Nasmyth cable-wrap side) or 'Prime'. PLATESCA is the plate scale at this focal station.
AUTOMODE, AUTOX and AUTOY record the guide loop status at the start of the observation, and the x,y reference position on the autoguider. At WHT Cassegrain, CAGARADI, CAGATHET, CAGAFOCU and CAGAFILT record the autoguider r and theta coordinates, focus and filter.
Other telescope headers: PARALLAX, RADECSYS and RADVEL.
UTOBS, UTSTART and ST (same as STSTART) record the time at the start of the observation. See the 'UT in the FITS headers' page for a discussion of the differences between UTOBS and UTSTART.
CCD and data-acquisition headers
The exposure time is recorded in EXPOSED = EXPTIME, ELAPSED, REQTIME and DARKTIME.
The name of the CCD is reproduced in CCDCHIP = CCDNAME = CHIPNAME = DETECTOR. Properties of the CCD are recorded in CCDTEMP, CCDTEMP1, CCDTEMP2, CCDTYPE, CCDXPIXE, CCDYPIXE, GAIN, MAXBIAS, READNOIS and SATURATE.
Other CCD/data headers include: AMPNAME, BSCALE, BZERO, DASCHAN, DISPAXIS, EXTNAME, EXTVER, GCOUNT, IMAGEID, INHERIT, PCOUNT and RTDATSEC.
The run number is recorded by RUN, IRAFNAME (same as RUN, but with preceding 'r') and RUNSET.
The value of OBSTYPE depends on whether the commands run, arc, flat, sky or dome were used at the telescope to obtain the data. The information is duplicated in IMAGETYP (required by iraf). The command used to obtain the exposure does not affect the values of any other FITS headers.
Last updated: 20 February 2019
|Top | Back|