INGRID WORK IN PROGRESS

OFFLINE WORK ACTIONS

Pupil Stop Z Axis Adjustment
1.1	Identify JH, K NAOMI stops	Maarten	asap	active
1.2	Compute optimum positions	Maarten	asap	active
1.4	Test results of adjustment and report	Chris	asap	active
K Band NAOMI Glow
2.1	Identify source	Paul	asap	active
2.2	Correct source	Paul	asap	active
Pupil Imager Characterization
3.1	Analyse pupil imager theoretical image quality	Maarten	asap	active
3.2	Analyse focus difference for NAOMI JH, K pupil stops	Maarten	asap	active
3.3	If favourable, optimise pupil imager for NAOMI use only	Paul / Maarten	asap	active
Pupil Stop and OSCA Mask Tangental Positions
4.1	Characterize	Chris	asap	active
4.2	Adjust EPICS tables	Dennis	asap	active
Thermal Management (Reduce Detector Temp.)
5.1	Calculate and engineer	Paul / Peter	asap	active
Documentation
6.1	Mechanical	Paul	asap	active
6.4	Scripts and reduction sw	???	asap	active
Epics Pupil Imager Control
7.1	Test EPICS control sequencing	Dennis	on hold	active
Cassagrain Mounting Bracket
8.1	Improve decoupling of axis	Paul	asap	active
8.2	Allow co-focal with AutoGuider	Paul	asap	active
Electronics Rack
9.1	Complete light weight unit	Kevin	asap	active
9.2	Fabricate and install Preamp clamp	Kevin	asap	active
LN2 Filler shield
10.1	Fabricate and install	Kevin	asap	active
Detector Noise Reduction
11.1	Further optimization	Peter	asap	active
A&G Box Large Flat
13.1	Test for correct operation at all angles	Peter	asap	active
Completion of Commissioning Tests
15.1	Analyse remaining tests for usefulness	Paul / Johan / Almu / Peter	asap	active
15.2	Repeat test 2.5.2 - Filter repeatability	Johan / Almu	asap	active
15.3	Repeat test 3.1.3 - Total system flexure test	Johan / Almu	asap	active
15.4	2.5.2 Repeatability of filters	Johan / Almu	asap	active
15.5	2.7.7 Folding flat repeatability	Johan / Almu	asap	active
15.6	2.8.3 Long term bias stability	Johan / Almu	asap	active
15.7	2.8.5 Stability after power cycle	Johan / Almu	asap	active
15.8	2.8.7 Flat field stability	Johan / Almu	asap	active
15.9	3.0.2 Focus offsets	Johan / Almu	asap	active
15.10	3.1.2 Plate scale and flexure	Johan / Almu	asap	active
15.11	3.6 Long term flat field stab.	Johan / Almu	asap	active
15.12	4.1 Dithering with autoguiding	Johan / Almu	asap	active
15.13	4.2 Dithering with autoguiding	Johan / Almu	asap	active
15.14	4.5.1 Pupil stop efficiency	Johan / Almu	asap	active
15.15	4.5.2 Pupil stop efficiency	Johan / Almu	asap	active
15.16	5.3 Vignetting of field	Johan / Almu	asap	active
15.17	5.5 Focus stability	Johan / Almu	asap	active
15.18	5.6 Autoguider vignetting	Johan / Almu	asap	active
15.19	5.7 Secondary baffle emmisions	Johan / Almu	asap	active
15.20	5.9 MNDR RON characterization	Johan / Almu	asap	active
INGRID Cosmetics
16.1	Design INGRID logo	anybody !	asap	active
16.2	Fabricate and fit name plate	Kevin	asap	active
16.3	Coat / paint vacuum jacket	Kevin / Paul	asap	active
INGRID UltraDas Commissioning
17.1	Test and evaluate UltraDas <--> SDSU code	Richard / Peter	asap	active
17.2	Install software at WHT	Richard / Dennis	asap	active
17.3	Test and evaluate system	Richard / Dennis	asap	active
17.4	UltraDas commissioning at Cass	Richard / Dennis	asap	active
17.5	UltraDas commissioning for NAOMI	Richard / Dennis	asap	active
AutoGuider Commissioning
18.1	Build code	Sheila	asap	active
18.2	Autoguider commissioning at Cass	Sheila / Richard	asap	active
Replacement of Cryogenic stepper motors
19.1	Contact Univ. Hawaii for report	Paul	URGENT	active
19.2	Issue report on feasability	Paul	URGENT	active
19.3	Procure replacement stepper motors	Paul	URGENT	active
19.4	Design and fabricate mounting brackets	Paul / Kevin	asap	active
19.5	Update EPICS motor records	Paul / Dennis	asap	active
Closed Cycle Cooler Reliability
20.1	Eliminate He Leaks	Kevin	asap	active
20.2	Install He line cold trap	Kevin	URGENT	active
Datum Switch Reliability
21.1	Contact IAC and report	Peter	asap	active
Electronics Spares
23.1	Assemble and test spare SDSU controller	Peter	asap	active
23.2	Prepare spare power supply and detector cable harness assy.	Peter	asap	active

DOWNTIME WORK ACTIONS

Pupil Stop Z Axis Adjustment
1.3	Adjust physical positions	Paul	asap	active
Thermal Management (Reduce Detector Temp.)
5.2	Rework thermal paths	Paul / Peter	asap	active
Clean Vacuum Space and Detector
12.1	Eliminate vacuum space contaminants	Peter	asap	active
12.2	Clean detector of debris	Peter	asap	active
INGRID Cosmetics
16.3	Coat / paint vacuum jacket	Kevin / Paul	asap	active
Replacement of Cryogenic stepper motors
19.6	Fit and test replacement motors	Paul / Kevin	asap	active
Vacuum Quality
22.1	Install absorber	Paul / Peter	asap	active
22.2	Super insulation replacement	Paul / Peter	asap	active
Repair Focus mechanism drive
24.1	Identify failure and report	Kevin / Paul	asap	active
24.2	Repair mechanism	Kevin / Paul	asap	active

COMPLETED WORK ACTIONS

Documentation
6.2	Electrical	Peter	30/11/01	done
6.3	Operational	Almu	30/11/01	done
6.3	Web Pages	Almu	30/11/01	done
Integration Timing Characterization
14.1	Test and document Version 3.1	Almu / Peter	30/11/01	done
14.2	Test and document Version 3.2	Almu / Peter	30/11/01	done
14.3	Test and document Version 4.0	Almu / Peter	30/11/01	done
Completion of Commissioning Tests
15.2	Repeat test 2.5.2 - Filter repeatability	Johan / Almu	30/11/01	done
15.3	Repeat test 3.1.3 - Total system flexure test	Johan / Almu	30/11/01	removed
15.4	2.5.2 Repeatability of filters	Johan / Almu	30/11/01	done
15.7	2.8.5 Stability after power cycle	Johan / Almu	30/11/01	removed
15.9	3.0.2 Focus offsets	Johan / Almu	30/11/01	done
15.10	3.1.2 Plate scale and flexure	Johan / Almu	30/11/01	done
15.17	5.5 Focus stability	Johan / Almu	30/11/01	done
15.18	5.6 Autoguider vignetting	Johan / Almu	30/11/01	done
15.20	5.9 MNDR RON characterization	Johan / Almu	30/11/01	done